Received your package.Checked the 24 pin. Its a lot of work to be done so it would definitely take a day or two.Also I've seen the layout of the wires in 8pin. All of them are fine. Checked again on a GPU.And I don't have a 8pin gpu extender so there is no alternate.Let me explain a bit . I hope you will got my point as there isnt much of a rocket science
So this is how a 8 pin gpu looks like . coming from any PSU
.
As you can see even in the original one there are 2 separate wires coming out. These are the black one.
BLACK is for Ground
Yellow is for +12V DC.
So in 8 PIn it has three +12V and 5 Ground wires.
A original PSU 8PIN GPU Connector uses this config
As long as black goes to black and yellow goes to yellow its fine.So i use this
Keeping this in mind there are tons of wires layout.
any alot more ;-)
This is why your are getting confused.However you can have this one.
he has shown some tremendous talent, skill in sleeving. its totally ULTRA quality. and is admirable to high. seen after a long time on PG. Its simply Awesome.
he has shown some tremendous talent, skill in sleeving. its totally ULTRA quality. and is admirable to high. seen after a long time on PG. Its simply Awesome.
Indeed his work is comendable but you got way over excited he is nice but it need some improvement like you can see the shrink tubings they are quite uneven see the work by [MENTION=7895]iameXtreme[/MENTION] [MENTION=20983]ovaisaijaz[/MENTION]
- - - Updated - - -
[MENTION=55830]yasirjamal[/MENTION] nice work bro liked almost all of them
Btw from where you getting sleeves wires and sockets with there pins for cramping ?
Indeed his work is comendable but you got way over excited he is nice but it need some improvement like you can see the shrink tubings they are quite uneven see the work by @iameXtreme @ovaisaijaz
- - - Updated - - -
@yasirjamal nice work bro liked almost all of them
Btw from where you getting sleeves wires and sockets with there pins for cramping ?
well, haven't heard from any one regarding any uneven work. infact @Dark Sith regular buying his work. and he is still ordering. there might be untideness, matter of fact, there is no 100%, in any work, 1% or 10% always left behind.............. but i would admire his work.
haven't get a chance to see others two modder's work. may be no thread of PG or i missed them.
he has shown some tremendous talent, skill in sleeving. its totally ULTRA quality. and is admirable to high. seen after a long time on PG. Its simply Awesome.
Indeed his work is comendable but you got way over excited he is nice but it need some improvement like you can see the shrink tubings they are quite uneven see the work by @iameXtreme @ovaisaijaz
- - - Updated - - -
@yasirjamal nice work bro liked almost all of them
Btw from where you getting sleeves wires and sockets with there pins for cramping ?
Agreed to [MENTION=4999]Pleasant[/MENTION], got some very nice suggestions from [MENTION=7895]iameXtreme[/MENTION] about the shrink tubing etc and tried different methods to make them look more sweeet.
Actually mdpcx and lutro customs sell all of the stuff required for the sleeving , they also sell premade heatshrinks which doesn't have diff on 0.0X of mm, if someone tried it he should be aware its alot easier than to cut each heatshrink manually like I do, even if i use surgical blades and stuff there is very slight +- in length and alignment, plus heatshrink has so many types, someones shrinks 1/3 of their size some poped up if heated too much some of them leave marks fingerprint on them if pressed. So ordering precutted shrinktubes are better to cut manually. IMO.
And also sleevings are of diff types too , some of them forms a mess on edges even if heated very very slightly. I might have the mdpcx sleeving somewhere in the store, will post a pic diff of the sleeving and the sleeving that is available on ebay etc can be seen.
BTW to avoid such mess of heatshrinks I now made the heatshrinkless sleevings with different methods and techniques. Still time taking but I love doing it and looks more beautiful without heatshrinks.
But yea one thing everytime I made them , i learn something I didn't know keeping the quality of wires unchanged from the time I've started it coz it doesn't need to be Just the aesthetics but also no compromise on quality, So in the end its getting better and better.
well, haven't heard from any one regarding any uneven work. infact @Dark Sith regular buying his work. and he is still ordering. there might be untideness, matter of fact, there is no 100%, in any work, 1% or 10% always left behind.............. but i would admire his work.
haven't get a chance to see others two modder's work. may be no thread of PG or i missed them.
the reason could be you may have joined the PG late or wasn't active in hardware / enthusiast zone there was a time when lots of Old Pg ppl were involved in modding scene now most of them have been got busy or calmed down
Thanks bro, Appreciate it.
Was in love with these and still love doing it
Agreed to [MENTION=4999]Pleasant[/MENTION], got some very nice suggestions from [MENTION=7895]iameXtreme[/MENTION] about the shrink tubing etc and tried different methods to make them look more sweeet.
Actually mdpcx and lutro customs sell all of the stuff required for the sleeving , they also sell premade heatshrinks which doesn't have diff on 0.0X of mm, if someone tried it he should be aware its alot easier than to cut each heatshrink manually like I do, even if i use surgical blades and stuff there is very slight +- in length and alignment, plus heatshrink has so many types, someones shrinks 1/3 of their size some poped up if heated too much some of them leave marks fingerprint on them if pressed. So ordering precutted shrinktubes are better to cut manually. IMO.
And also sleevings are of diff types too , some of them forms a mess on edges even if heated very very slightly. I might have the mdpcx sleeving somewhere in the store, will post a pic diff of the sleeving and the sleeving that is available on ebay etc can be seen.
BTW to avoid such mess of heatshrinks I now made the heatshrinkless sleevings with different methods and techniques. Still time taking but I love doing it and looks more beautiful without heatshrinks.
But yea one thing everytime I made them , i learn something I didn't know keeping the quality of wires unchanged from the time I've started it coz it doesn't need to be Just the aesthetics but also no compromise on quality, So in the end its getting better and better.
yeah i know what you are saying about shrinks and sleevings, i have also done the sleevings i have used both pre cut and the bigger coil shrinks , pre cut stuff is for Pros who got master after redoing it coil one is good for starters and newbie because you can fix your mistakes if you cut off smaller sleeves then you can accompany it with bit longer Shrinks as you might have ordered limited quantity of sleeves you so discarding and redoing the sleeve may fall short for rest of wires if you ordered big coil then you are good to go with precut stuff and you can redo till perfection yeah i have seen ppl doing shrinkless sleeves as well what they told me they solder the end of shrinks and it does the job for them
I have two question from where you getting the Sleeves, Wires, shrinks and pins Black 8pin 24pin 6pin connector , which cramping tool you using are you using mdpcx stuff? you getting directly from MDPCX ?
For Extensions creation we put the wire in same holes from one end to another end ?
the reason could be you may have joined the PG late or wasn't active in hardware / enthusiast zone there was a time when lots of Old Pg ppl were involved in modding scene now most of them have been got busy or calmed down
well joined PG far back in 2010. but the time when activities are at its peak level i wasn't there/active much in hardware section. thats why i missed so many awesomenesses.
I have two question from where you getting the Sleeves, Wires, shrinks and pins Black 8pin 24pin 6pin connector , which cramping tool you using are you using mdpcx stuff? you getting directly from MDPCX ?
no idea how that is a steal by wasting 3500 rupees per month and for games that are removed before you can finish them off.xbox gamepass is garbage with no local prices
no idea how that is a steal by wasting 3500 rupees per month and for games that are removed before you can finish them off.xbox gamepass is garbage with no local prices
Just finished Diablo 4 season in hurry to play Fallout 4 but gamepass released another banger in the form of Star Wars on April 25th. Gamepass is a steal man.
Is it just me or people lately seem to defend every bad game design decision made by the devs and try to give bullshit reasons for that? Or perhaps it's because I'm on reddit and discord
Is it just me or people lately seem to defend every bad game design decision made by the devs and try to give bullshit reasons for that? Or perhaps it's because I'm on reddit and discord